Now that I’ve made a serial cable I can now show you the full boot messages starting from U-Boot.
U-Boot 2012.07 (Sep 13 2013 - 13:53:58) for Exynos5410
CPU: Exynos5410 Rev2.3 [Samsung SOC on SMP Platform Base on ARM CortexA15]
APLL = 900MHz, KPLL = 600MHz
MPLL = 532MHz, BPLL = 800MHz
DRAM: 2 GiB
WARNING: Caches not enabled
TrustZone Enabled BSP
BL1 version:
PMIC VER : 0, CHIP REV : 6
VDD MIF : 1.00000V
VDD ARM : 1.00000V
VDD INT : 1.00000V
VDD G3D : 1.00000V
VDD KFC : 1.00000V
Checking Boot Mode ... SDMMC
MMC: S5P_MSHC2: 0, S5P_MSHC0: 1
MMC Device 0: 29.7 GiB
MMC Device 1: [ERROR] response error : 00000006 cmd 8
[ERROR] response error : 00000006 cmd 55
[ERROR] response error : 00000006 cmd 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Press 'Enter' or 'Space' to stop autoboot: 1 0
there are pending interrupts 0x00000001
reading boot.ini
5510 bytes read
Find boot.ini file from FAT Area!!
boot.ini command = setenv hk_current_version "2"
boot.ini command = setenv verify 'if test $hk_version != $hk_current_version;then;fatload mmc 0:1 40008000 u-boot.bin;emmc open 0;movi w z u 0 40008000;emmc close 0;setenv hk_version $hk_current_version;save;reset;fi'
boot.ini command = run verify
reading u-boot.bin
293168 bytes read
[ERROR] response timeout error : 00000104 cmd 6
eMMC OPEN Failed.!!
boot.ini command = setenv initrd_high "0xffffffff"
boot.ini command = setenv fdt_high "0xffffffff"
boot.ini command = setenv bootrootfs "console=tty1 console=ttySAC2,115200n8 root=UUID=ad455a75-609c-4b3c-956b-bcef3ebc4603 rhgb rootwait ro"
boot.ini command = setenv fb_x_res "1280"
boot.ini command = setenv fb_y_res "720"
boot.ini command = setenv vout "hdmi"
boot.ini command = setenv left "56"
boot.ini command = setenv right "24"
boot.ini command = setenv upper "3"
boot.ini command = setenv lower "3"
boot.ini command = setenv hsync "14"
boot.ini command = setenv vsync "3"
boot.ini command = setenv fb_control "left=${left} right=${right} upper=${upper} lower=${lower} vsync=${vsync} hsync=${hsync}"
boot.ini command = setenv hdmi_phy_res "720p60hz"
boot.ini command = setenv led_blink "1"
boot.ini command = setenv bootcmd "fatload mmc 0:1 0x40008000 zImage; fatload mmc 0:1 0x42000000 uInitrd; bootz 0x40008000 0x42000000"
boot.ini command = setenv bootargs "${bootrootfs} ${fb_control} fb_x_res=${fb_x_res} fb_y_res=${fb_y_res} vout=${vout} hdmi_phy_res=${hdmi_phy_res} led_blink=${led_blink}"
boot.ini command = boot
reading zImage
5127832 bytes read
reading uInitrd
6518598 bytes read
## Loading init Ramdisk from Legacy Image at 42000000 ...
Image Name: uInitrd 3.4.5
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 6518534 Bytes = 6.2 MiB
Load Address: 00000000
Entry Point: 00000000
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.5 (root@odroid-server) (gcc version 4.7.3 (Ubuntu/Linaro 4.7.3-1ubuntu1) ) #1 SMP PREEMPT Fri Sep 27 02:59:27 BRT 2013
[ 0.000000] CPU: ARMv7 Processor [412fc0f3] revision 3 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: ODROIDXU
[ 0.000000] S5P/CMA: Reserved 0x08000000@0xb7e00000 for 'ion'
[ 0.000000] S5P/CMA: Reserved 0x00100000@0xb7d00000 for 'drm_mfc_sh'
[ 0.000000] S5P/CMA: Reserved 0x00c00000@0xb7100000 for 'drm_g2d_wfd'
[ 0.000000] S5P/CMA: Reserved 0x00400000@0xac000000 for 'drm_sectbl'
[ 0.000000] S5P/CMA: Reserved 0x00100000@0xac400000 for 'drm_mfc_fw'
[ 0.000000] S5P/CMA: Reserved 0x01000000@0xac500000 for 'drm_mfc_input'
[ 0.000000] S5P/CMA: Reserved 0x03b00000@0xad500000 for 'drm_mfc_output'
[ 0.000000] S5P/CMA: Reserved 0x03000000@0xb1000000 for 'drm_fimd_video'
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU EXYNOS5410 (id 0xe5410023)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] EXYNOS5: EAGLECLK=900000000, KFCCLK=600000000, CDREX=800000000
[ 0.000000] mout_apll: source is fout_apll (1), rate is 900000000
[ 0.000000] mout_mpll: source is fout_mpll (1), rate is 532000000
[ 0.000000] mout_epll: source is fout_epll (1), rate is 400000000
[ 0.000000] mout_bpll: source is fout_bpll (1), rate is 800000000
[ 0.000000] mout_cpll: source is fout_cpll (1), rate is 640000000
[ 0.000000] mout_kpll: source is fout_kpll (1), rate is 600000000
[ 0.000000] mout_ipll: source is fout_ipll (1), rate is 432000000
[ 0.000000] aclk_333_432_isp: source is ext_xtal (0), rate is 24000000
[ 0.000000] aclk_333_432_gscl: source is ext_xtal (0), rate is 24000000
[ 0.000000] vpll_src: source is ext_xtal (0), rate is 24000000
[ 0.000000] mout_vpll: source is fout_vpll (1), rate is 350000000
[ 0.000000] mout_mpll_user: source is mout_mpll (1), rate is 532000000
[ 0.000000] mout_bpll_user: source is mout_bpll (1), rate is 800000000
[ 0.000000] mout_mpll_bpll: source is mout_bpll_user (1), rate is 800000000
[ 0.000000] mout_dpll: source is fout_dpll (1), rate is 600000000
[ 0.000000] aclk_400: source is mout_mpll_user (0), rate is 177333333
[ 0.000000] aclk_400_isp_pre: source is mout_mpll_user (0), rate is 66500000
[ 0.000000] aclk_400_isp: source is ext_xtal (0), rate is 24000000
[ 0.000000] aclk_266_isp: source is ext_xtal (0), rate is 24000000
[ 0.000000] aclk_200: source is mout_mpll_user (0), rate is 177333333
[ 0.000000] aclk_200_disp1: source is ext_xtal (0), rate is 24000000
[ 0.000000] aclk_166: source is mout_cpll (0), rate is 160000000
[ 0.000000] mout_cpu: source is mout_apll (0), rate is 900000000
[ 0.000000] mout_cpu_kfc: source is mout_kpll (0), rate is 600000000
[ 0.000000] sclk_mmc0: source is mout_mpll_bpll (6), rate is 800000000
[ 0.000000] sclk_mmc1: source is mout_mpll_bpll (6), rate is 72727272
[ 0.000000] sclk_mmc2: source is mout_mpll_bpll (6), rate is 800000000
[ 0.000000] sclk_pwm_isp: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_uart_isp: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi1_isp: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi0_isp: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_mout_isp_sensor: source is mout_ipll (0), rate is 432000000
[ 0.000000] sclk_mau_audio0: source is ext_xtal (1), rate is 24000000
[ 0.000000] mout_g3d: source is mout_cpll (0), rate is 640000000
[ 0.000000] sclk_g3d_core_sub: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_g3d_hydra_sub: source is ext_xtal (0), rate is 24000000
[ 0.000000] clkout: source is xxti (16), rate is 24000000
[ 0.000000] aclk_300_disp1: source is ext_xtal (0), rate is 24000000
[ 0.000000] uclk1: source is mout_cpll (9), rate is 64000000
[ 0.000000] uclk1: source is mout_cpll (9), rate is 64000000
[ 0.000000] uclk1: source is mout_cpll (9), rate is 64000000
[ 0.000000] uclk1: source is mout_cpll (9), rate is 64000000
[ 0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c1d12000 s11840 r8192 d12736 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519172
[ 0.000000] Kernel command line: console=ttySAC2,115200n8 vmalloc=512M console=tty1 console=ttySAC2,115200n8 root=UUID=ad455a75-609c-4b3c-956b-bcef3ebc4603 rhgb rootwait ro left=56 right=24 upper=3 lower=3 vsync=3 hsync=14 fb_x_res=1280 fb_y_res=720 vout=hdmi hdmi_phy_res=720p60hz led_blink=1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 2046MB = 2046MB total
[ 0.000000] Memory: 1782924k/1782924k available, 312180k reserved, 1311744K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0952000 (9512 kB)
[ 0.000000] .init : 0xc0952000 - 0xc0991e40 ( 256 kB)
[ 0.000000] .data : 0xc0992000 - 0xc0a3a5a0 ( 674 kB)
[ 0.000000] .bss : 0xc0a3a5c4 - 0xc0b04b90 ( 810 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:693
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.001171] Calibrating delay loop... 1785.85 BogoMIPS (lpj=4464640)
[ 0.045051] pid_max: default: 32768 minimum: 301
[ 0.045356] Mount-cache hash table entries: 512
[ 0.046178] Initializing cgroup subsys debug
[ 0.046202] Initializing cgroup subsys cpuacct
[ 0.046222] Initializing cgroup subsys devices
[ 0.046242] Initializing cgroup subsys freezer
[ 0.046294] CPU: Testing write buffer coherency: ok
[ 0.046445] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.046515] Setting up static identity map for 0x406dc7b0 - 0x406dc808
[ 0.097732] CPU1: Booted secondary processor
[ 0.097758] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.117733] CPU2: Booted secondary processor
[ 0.117763] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.137725] CPU3: Booted secondary processor
[ 0.137751] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.137884] Brought up 4 CPUs
[ 0.137968] SMP: Total of 4 processors activated (7143.42 BogoMIPS).
[ 0.138658] devtmpfs: initialized
[ 0.154727] gpiochip_add: registered GPIOs 0 to 4 on device: GPJ0
[ 0.154758] gpiochip_add: registered GPIOs 6 to 13 on device: GPJ1
[ 0.154783] gpiochip_add: registered GPIOs 15 to 22 on device: GPJ2
[ 0.154807] gpiochip_add: registered GPIOs 24 to 31 on device: GPJ3
[ 0.154830] gpiochip_add: registered GPIOs 33 to 34 on device: GPJ4
[ 0.154853] gpiochip_add: registered GPIOs 36 to 43 on device: GPK0
[ 0.154876] gpiochip_add: registered GPIOs 45 to 52 on device: GPK1
[ 0.154899] gpiochip_add: registered GPIOs 54 to 61 on device: GPK2
[ 0.154922] gpiochip_add: registered GPIOs 63 to 69 on device: GPK3
[ 0.154955] gpiochip_add: registered GPIOs 71 to 78 on device: GPA0
[ 0.154978] gpiochip_add: registered GPIOs 80 to 85 on device: GPA1
[ 0.155001] gpiochip_add: registered GPIOs 87 to 94 on device: GPA2
[ 0.155024] gpiochip_add: registered GPIOs 96 to 100 on device: GPB0
[ 0.155046] gpiochip_add: registered GPIOs 102 to 106 on device: GPB1
[ 0.155069] gpiochip_add: registered GPIOs 108 to 111 on device: GPB2
[ 0.155092] gpiochip_add: registered GPIOs 113 to 116 on device: GPB3
[ 0.155116] gpiochip_add: registered GPIOs 118 to 124 on device: GPC0
[ 0.155139] gpiochip_add: registered GPIOs 126 to 129 on device: GPC3
[ 0.155162] gpiochip_add: registered GPIOs 131 to 137 on device: GPC1
[ 0.155185] gpiochip_add: registered GPIOs 139 to 145 on device: GPC2
[ 0.155208] gpiochip_add: registered GPIOs 147 to 148 on device: GPM5
[ 0.155231] gpiochip_add: registered GPIOs 150 to 157 on device: GPD1
[ 0.155254] gpiochip_add: registered GPIOs 159 to 166 on device: GPE0
[ 0.155277] gpiochip_add: registered GPIOs 168 to 169 on device: GPE1
[ 0.155300] gpiochip_add: registered GPIOs 171 to 176 on device: GPF0
[ 0.155323] gpiochip_add: registered GPIOs 178 to 185 on device: GPF1
[ 0.155346] gpiochip_add: registered GPIOs 187 to 194 on device: GPG0
[ 0.155369] gpiochip_add: registered GPIOs 196 to 203 on device: GPG1
[ 0.155392] gpiochip_add: registered GPIOs 205 to 206 on device: GPG2
[ 0.155415] gpiochip_add: registered GPIOs 208 to 211 on device: GPH0
[ 0.155437] gpiochip_add: registered GPIOs 213 to 220 on device: GPH1
[ 0.155460] gpiochip_add: registered GPIOs 222 to 229 on device: GPM7
[ 0.155483] gpiochip_add: registered GPIOs 231 to 236 on device: GPY0
[ 0.155506] gpiochip_add: registered GPIOs 238 to 241 on device: GPY1
[ 0.155529] gpiochip_add: registered GPIOs 243 to 248 on device: GPY2
[ 0.155552] gpiochip_add: registered GPIOs 250 to 257 on device: GPY3
[ 0.155575] gpiochip_add: registered GPIOs 259 to 266 on device: GPY4
[ 0.155598] gpiochip_add: registered GPIOs 268 to 275 on device: GPY5
[ 0.155621] gpiochip_add: registered GPIOs 277 to 284 on device: GPY6
[ 0.155644] gpiochip_add: registered GPIOs 286 to 293 on device: GPY7
[ 0.155667] gpiochip_add: registered GPIOs 295 to 302 on device: GPX0
[ 0.155690] gpiochip_add: registered GPIOs 304 to 311 on device: GPX1
[ 0.155713] gpiochip_add: registered GPIOs 313 to 320 on device: GPX2
[ 0.155735] gpiochip_add: registered GPIOs 322 to 329 on device: GPX3
[ 0.155765] gpiochip_add: registered GPIOs 331 to 338 on device: GPV0
[ 0.155788] gpiochip_add: registered GPIOs 340 to 347 on device: GPV1
[ 0.155811] gpiochip_add: registered GPIOs 349 to 356 on device: GPV2
[ 0.155833] gpiochip_add: registered GPIOs 358 to 365 on device: GPV3
[ 0.155856] gpiochip_add: registered GPIOs 367 to 368 on device: GPV4
[ 0.155890] gpio: GPZ has no PM function
[ 0.155908] gpiochip_add: registered GPIOs 370 to 376 on device: GPZ
[ 0.156524] dummy:
[ 0.156864] NET: Registered protocol family 16
[ 0.160484] Last reset was reset (RST_STAT=0x100)
[ 0.170775] odroidxu_clkout_init [496] : clkout_clk = 24000000
[ 0.170782]
[ 0.178288]
[ 0.178293] ---------------------------------------------------------
[ 0.178299]
[ 0.178334] exynos5_odroidxu_display_init : LCD or HDMI or DVI Monitor!
[ 0.178357]
[ 0.178360] ---------------------------------------------------------
[ 0.178365]
[ 0.178395]
[ 0.178398] ---------------------------------------------------------
[ 0.178404]
[ 0.178433] Virtual FB Size from Boot Parameter : X(1280), y(720)
[ 0.178454]
[ 0.178457] ---------------------------------------------------------
[ 0.178463]
[ 0.180940] CCI is not supportedS3C Power Management, Copyright 2004 Simtec Electronics
[ 0.182106] PowerDomain : pd-mfc, Device : s5p-mfc-v6 Registered
[ 0.182146] PowerDomain : pd-mipi-csis0, Device : s5p-mipi-csis Registered
[ 0.182178] PowerDomain : pd-mipi-csis1, Device : s5p-mipi-csis Registered
[ 0.182208] PowerDomain : pd-mipi-csis2, Device : s5p-mipi-csis Registered
[ 0.182246] PowerDomain : pd-flite0, Device : exynos-fimc-lite Registered
[ 0.182276] PowerDomain : pd-flite1, Device : exynos-fimc-lite Registered
[ 0.182311] PowerDomain : pd-flite2, Device : exynos-fimc-lite Registered
[ 0.182341] PowerDomain : pd-maudio, Device : samsung-i2s Registered
[ 0.182373] PowerDomain : pd-fimd1, Device : exynos5-fb Registered
[ 0.182404] PowerDomain : pd-mipi_dsim, Device : s5p-mipi-dsim Registered
[ 0.182438] PowerDomain : pd-hdmi, Device : exynos5-hdmi Registered
[ 0.182466] PowerDomain : pd-mixer, Device : s5p-mixer Registered
[ 0.182505] PowerDomain : pd-gscl0, Device : exynos-gsc Registered
[ 0.182533] PowerDomain : pd-gscl1, Device : exynos-gsc Registered
[ 0.182560] PowerDomain : pd-gscl2, Device : exynos-gsc Registered
[ 0.182588] PowerDomain : pd-gscl3, Device : exynos-gsc Registered
[ 0.182615] PowerDomain : pd-gscl4, Device : exynos5-scaler Registered
[ 0.182647] PowerDomain : pd-g3d, Device : pvrsrvkm Registered
[ 0.182675] PowerDomain : pd-g2d, Device : s5p-fimg2d Registered
[ 0.182703] PowerDomain : pd-gscl, Device : exynos-sysmmu Registered
[ 0.182732] PowerDomain : pd-gscl, Device : exynos-sysmmu Registered
[ 0.182764] PowerDomain : pd-gscl, Device : exynos-sysmmu Registered
[ 0.182804] PowerDomain : pd-gscl0, Device : exynos-sysmmu Registered
[ 0.182835] PowerDomain : pd-gscl1, Device : exynos-sysmmu Registered
[ 0.182864] PowerDomain : pd-gscl2, Device : exynos-sysmmu Registered
[ 0.182892] PowerDomain : pd-gscl3, Device : exynos-sysmmu Registered
[ 0.182920] PowerDomain : pd-gscl, Device : exynos-sysmmu Registered
[ 0.182948] PowerDomain : pd-gscl, Device : exynos-sysmmu Registered
[ 0.182976] PowerDomain : pd-gscl4, Device : exynos-sysmmu Registered
[ 0.183005] PowerDomain : pd-fimd1, Device : exynos-sysmmu Registered
[ 0.183033] PowerDomain : pd-mixer, Device : exynos-sysmmu Registered
[ 0.183061] PowerDomain : pd-isp, Device : exynos-sysmmu Registered
[ 0.183088] PowerDomain : pd-isp, Device : exynos-sysmmu Registered
[ 0.183116] PowerDomain : pd-isp, Device : exynos-sysmmu Registered
[ 0.183143] PowerDomain : pd-mfc, Device : exynos-sysmmu Registered
[ 0.183171] PowerDomain : pd-g2d, Device : exynos-sysmmu Registered
[ 0.183302] Failed to get (null) clock
[ 0.183631] EXYNOS5410 PMU Initialize
[ 0.184249] EXYNOS: Initializing architecture
[ 0.185403] s3c24xx-pwm s3c24xx-pwm.0: tin at 2015151, tdiv at 2015151, tin=divclk, base 0
[ 0.185517] s3c24xx-pwm s3c24xx-pwm.3: tin at 33250000, tdiv at 33250000, tin=divclk, base 16
[ 0.186526] Exynos5410 : Lot ID is N68Z5[Non Special]
[ 0.186549] Exynos5410 ASV : Use Fusing Speed Group 4
[ 0.186569] Exynos5410 ASV : invalid IDS value
[ 0.186588] EXYNOS5410 ASV : N68Z5 IDS : 0 HPM : 0
[ 0.186617] VDD_ARM ASV group is 4
[ 0.186637] VDD_KFC ASV group is 4
[ 0.186656] VDD_INT_MIF_L0 ASV group is 4
[ 0.186676] VDD_MIF ASV group is 4
[ 0.186693] VDD_G3D ASV group is 4
[ 0.186710] VDD_INT_MIF_L1 ASV group is 4
[ 0.186730] VDD_INT_MIF_L2 ASV group is 4
[ 0.186749] VDD_INT_MIF_L3 ASV group is 4
[ 0.188015] Exynos Power mode List
[ 0.188033] NAME CPU MIF INT CPU0 CPU1 CPU2 CPU3
[ 0.188057] init 0 0 0 1 1 1 1
[ 0.188075] quad 1600000 800000 400000 1 1 1 1
[ 0.188095] quad_io 1800000 800000 400000 1 1 0 0
[ 0.188115] quad_mem 1800000 800000 400000 1 1 0 0
[ 0.188146] exynos_interface_init: failed to create sysfs interface
[ 0.222501] bio: create slab at 0
[ 0.224976] DC_5V: 5000 mV
[ 0.226718] SCSI subsystem initialized
[ 0.228191] usbcore: registered new interface driver usbfs
[ 0.228479] usbcore: registered new interface driver hub
[ 0.228676] usbcore: registered new device driver usb
[ 0.229804] i2c-gpio i2c-gpio.2: using pins 77 (SDA) and 78 (SCL)
[ 0.230390] i2c-gpio i2c-gpio.10: using pins 323 (SDA) and 311 (SCL)
[ 0.230997] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.231023] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.231044] s3c-i2c s3c2440-i2c.1: bus frequency set to 377 KHz
[ 0.231522] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.231547] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.231569] s3c-i2c s3c2440-i2c.0: bus frequency set to 377 KHz
[ 0.231627] s3c-i2c s3c2440-i2c.2: no platform data
[ 0.231657] s3c-i2c: probe of s3c2440-i2c.2 failed with error -22
[ 0.232409] max77802 4-0009: device found
[ 0.232431] max77802_irq_init+
[ 0.232454] max77802_irq_init: gpio_irq=0
[ 0.237385] max77802_irq_init-
[ 0.239285] vdd_mif range: 800 1300 mV at 1000 mV
[ 0.239998] vdd_arm range: 800 1500 mV at 1000 mV
[ 0.240702] vdd_int range: 800 1400 mV at 1000 mV
[ 0.241404] vdd_g3d range: 800 1400 mV at 1000 mV
[ 0.242135] vdd_mem2 range: 800 1500 mV at 1200 mV
[ 0.242840] vdd_kfc range: 800 1500 mV at 1000 mV
[ 0.243747] vdd_alive: 1000 mV
[ 0.244665] vddq_M1_M2: 1200 mV
[ 0.245562] vddq_gpio: 1800 mV
[ 0.246467] vddq_mmc2: 2800 mV
[ 0.247380] vdd18_hsic: 1800 mV
[ 0.248292] vdd18_BPLL: 1800 mV
[ 0.248999] vddq_lcd: 1800 mV
[ 0.249908] vdd10_hdmi: 1000 mV
[ 0.250803] vdd18_mipi: 1800 mV
[ 0.251729] vddq_mmc01: 1800 mV
[ 0.252626] vdd33_USB30: 3300 mV
[ 0.253528] vddq_abb0: 1800 mV
[ 0.254429] vddq_abb1: 1800 mV
[ 0.255324] vdd10_USB30: 1000 mV
[ 0.256012] cam_sensor_core: 1200 mV
[ 0.256717] LDO18: 1800 mV
[ 0.257628] vdd_emmc_1v8: 1800 mV
[ 0.258526] VDDF_2V8: 2850 mV
[ 0.259423] DP_P3V3: 3300 mV
[ 0.260106] cam_af_2.8v: 2800 mV
[ 0.261009] ETH_P3V3: 3300 mV
[ 0.261903] USB30_EXTCLK: 3300 mV
[ 0.262812] vddq_E12: 1200 mV
[ 0.264836] vs_power_meter: 3300 mV
[ 0.266116] exynos5-i2c exynos5-hs-i2c.0: i2c-4: Exynos5 HS-I2C adapter
[ 0.266310] Linux media interface: v0.10
[ 0.266469] Linux video capture interface: v2.00
[ 0.272888] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.273791] Bluetooth: Core ver 2.16
[ 0.273948] NET: Registered protocol family 31
[ 0.273969] Bluetooth: HCI device and connection manager initialized
[ 0.273996] Bluetooth: HCI socket layer initialized
[ 0.274016] Bluetooth: L2CAP socket layer initialized
[ 0.274066] Bluetooth: SCO socket layer initialized
[ 0.274576] cfg80211: Calling CRDA to update world regulatory domain
[ 0.275168] nfc: nfc_init: NFC Core ver 0.1
[ 0.275355] NET: Registered protocol family 39
[ 0.275660] Switching to clocksource mct-frc
[ 0.314333] NET: Registered protocol family 2
[ 0.314543] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.315006] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.316188] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.317389] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.317413] TCP: reno registered
[ 0.317434] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.317471] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.317712] NET: Registered protocol family 1
[ 0.318027] RPC: Registered named UNIX socket transport module.
[ 0.318054] RPC: Registered udp transport module.
[ 0.318073] RPC: Registered tcp transport module.
[ 0.318093] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.318285] Trying to unpack rootfs image as initramfs...
[ 0.686071] Freeing initrd memory: 6364K
[ 0.687316] big.LITTLE switcher initializing
[ 0.698644] big.LITTLE switcher initialized
[ 0.698821] s3c-adc samsung-adc-v5: operating without regulator "vdd" .
[ 0.698908] s3c-adc samsung-adc-v5: attached adc driver
[ 0.701070] highmem bounce pool size: 64 pages
[ 0.720132] NFS: Registering the id_resolver key type
[ 0.721670] NTFS driver 2.1.30 [Flags: R/W DEBUG].
[ 0.721997] fuse init (API version 7.18)
[ 0.722869] msgmni has been set to 932
[ 0.725245] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.725279] io scheduler noop registered
[ 0.725299] io scheduler deadline registered
[ 0.725601] io scheduler cfq registered (default)
[ 0.733641] dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
[ 0.733674] dma-pl330 dma-pl330.0: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.740909] dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
[ 0.740942] dma-pl330 dma-pl330.1: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.742896] dma-pl330 dma-pl330.2: Loaded driver for PL330 DMAC-267056
[ 0.742927] dma-pl330 dma-pl330.2: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 0.743448] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.745308] exynos4210-uart.0: ttySAC0 at MMIO 0x12c00000 (irq = 83) is a S3C6400/10
[ 0.745694] exynos4210-uart.1: ttySAC1 at MMIO 0x12c10000 (irq = 84) is a S3C6400/10
[ 0.746156] exynos4210-uart.2: ttySAC2 at MMIO 0x12c20000 (irq = 85) is a S3C6400/10
[ 2.609045] console [ttySAC2] enabled
[ 2.613011] exynos4210-uart.3: ttySAC3 at MMIO 0x12c30000 (irq = 86) is a S3C6400/10
[ 2.621365] ion_device_add_heap: can not insert multiple heaps with id 1
[ 2.627040] ion_device_add_heap: can not insert multiple heaps with id 0
[ 2.634087] PVR_K: PVRSRVDriverProbe(pDevice=c09ddc18)
[ 2.638834] PVR_K: SysInitialise: start
[ 2.643544] PVR_K: G3D DVFS Info: Level:0, Clock:640 MHz, Voltage:1150000 uV
[ 2.649676] PVR_K: G3D DVFS Info: Level:1, Clock:532 MHz, Voltage:1087500 uV
[ 2.656706] PVR_K: G3D DVFS Info: Level:2, Clock:480 MHz, Voltage:1050000 uV
[ 2.663722] PVR_K: G3D DVFS Info: Level:3, Clock:350 MHz, Voltage:937500 uV
[ 2.670657] PVR_K: G3D DVFS Info: Level:4, Clock:266 MHz, Voltage:900000 uV
[ 2.677596] PVR_K: G3D DVFS Info: Level:5, Clock:177 MHz, Voltage:900000 uV
[ 2.684921] PVR_K: enable_gpu_power off fail with pm_runtime_suspended
[ 2.691043] PVR_K: SysInitialise: end
[ 2.747184] brd: module loaded
[ 2.756001] loop: module loaded
[ 2.758703] tun: Universal TUN/TAP device driver, 1.6
[ 2.762734] tun: (C) 1999-2004 Max Krasnyansky
[ 2.769249] PPP generic driver version 2.4.2
[ 2.773654] PPP BSD Compression module registered
[ 2.777820] PPP Deflate Compression module registered
[ 2.784896] PPP MPPE Compression module registered
[ 2.788255] NET: Registered protocol family 24
[ 2.792896] usbcore: registered new interface driver asix
[ 2.798237] usbcore: registered new interface driver ax88179_178a
[ 2.804285] usbcore: registered new interface driver cdc_ether
[ 2.810095] usbcore: registered new interface driver cdc_subset
[ 2.816052] usbcore: registered new interface driver ipheth
[ 2.821546] usbcore: registered new interface driver cdc_ncm
[ 2.827164] exynos-drd exynos-dwc3.0: Core ID Number: 0x5533
[ 2.832654] exynos-drd exynos-dwc3.0: Release Number: 0x200a
[ 2.838451] exynos-drd exynos-dwc3.0: IRQ: ID: 1
[ 2.842993] exynos-drd exynos-dwc3.0: IRQ: VBUS: inactive
[ 2.848854] exynos-drd exynos-dwc3.1: Core ID Number: 0x5533
[ 2.853902] exynos-drd exynos-dwc3.1: Release Number: 0x200a
[ 2.859689] exynos-drd exynos-dwc3.1: IRQ: VBUS: inactive
[ 2.865610] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.895807] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 2.899588] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 2.906689] s5p-ehci s5p-ehci: irq 103, io mem 0x12110000
[ 2.920815] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 2.925631] hub 1-0:1.0: USB hub found
[ 2.928512] hub 1-0:1.0: 3 ports detected
[ 2.933218] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.938827] exynos-ohci exynos-ohci: Already power on PHY
[ 2.944025] exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller
[ 2.950020] exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 2
[ 2.957593] exynos-ohci exynos-ohci: irq 103, io mem 0x12120000
[ 3.020640] hub 2-0:1.0: USB hub found
[ 3.022960] hub 2-0:1.0: 3 ports detected
[ 3.027700] exynos-drd exynos-dwc3.0: Core ID Number: 0x5533
[ 3.032632] exynos-drd exynos-dwc3.0: Release Number: 0x200a
[ 3.038218] exynos-xhci exynos-xhci.0: EXYNOS xHCI Host Controller
[ 3.044379] exynos-xhci exynos-xhci.0: new USB bus registered, assigned bus number 3
[ 3.052267] exynos-xhci exynos-xhci.0: irq 104, io mem 0x12000000
[ 3.059032] hub 3-0:1.0: USB hub found
[ 3.061899] hub 3-0:1.0: 1 port detected
[ 3.066267] exynos-xhci exynos-xhci.0: EXYNOS xHCI Host Controller
[ 3.071958] exynos-xhci exynos-xhci.0: new USB bus registered, assigned bus number 4
[ 3.080406] hub 4-0:1.0: USB hub found
[ 3.083423] hub 4-0:1.0: 1 port detected
[ 3.087861] exynos-drd exynos-dwc3.1: Core ID Number: 0x5533
[ 3.092934] exynos-drd exynos-dwc3.1: Release Number: 0x200a
[ 3.098572] exynos-xhci exynos-xhci.1: EXYNOS xHCI Host Controller
[ 3.104735] exynos-xhci exynos-xhci.1: new USB bus registered, assigned bus number 5
[ 3.112619] exynos-xhci exynos-xhci.1: irq 232, io mem 0x12400000
[ 3.119341] hub 5-0:1.0: USB hub found
[ 3.122249] hub 5-0:1.0: 1 port detected
[ 3.126603] exynos-xhci exynos-xhci.1: EXYNOS xHCI Host Controller
[ 3.132354] exynos-xhci exynos-xhci.1: new USB bus registered, assigned bus number 6
[ 3.140923] hub 6-0:1.0: USB hub found
[ 3.143727] hub 6-0:1.0: 1 port detected
[ 3.148648] usbcore: registered new interface driver cdc_acm
[ 3.153288] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.161268] Initializing USB Mass Storage driver...
[ 3.166442] usbcore: registered new interface driver usb-storage
[ 3.172105] USB Mass Storage support registered.
[ 3.177150] usbcore: registered new interface driver usbserial
[ 3.182533] usbserial: USB Serial Driver core
[ 3.187083] usbcore: registered new interface driver pl2303
[ 3.192596] USB Serial support registered for pl2303
[ 3.240842] usb 1-2: new high-speed USB device number 2 using s5p-ehci
[ 3.301305] usb3503 4-0008: switched to HUB mode
[ 3.304452] usb3503 4-0008: usb3503_probe: probed on hub mode
[ 3.310814] exynos-ss-udc exynos-ss-udc.0: regs df8b2000, irq 104
[ 3.316944] exynos-ss-udc exynos-ss-udc.1: regs df8be000, irq 232
[ 3.323488] gadget: Gadget Serial v2.4
[ 3.326254] gadget: g_serial ready
[ 3.329684] exynos-ss-udc exynos-ss-udc.0: bound driver g_serial
[ 3.336464] mousedev: PS/2 mouse device common for all mice
[ 3.341462] odroid_keypad_init
[ 3.344723] input: odroid-keypad as /devices/virtual/input/input0
[ 3.350366] odroid_keypad_open
[ 3.353670] --------------------------------------------------------
[ 3.359726] odroid-keypad driver initialized!! Ver 1.0
[ 3.364875] --------------------------------------------------------
[ 3.371226] platform_driver_register 0
[ 3.375162] usbcore: registered new interface driver xpad
[ 3.431679] odroid-ts 0-0048: I2C write error: (-6) reg: 0x4 len: 0
[ 3.436882] input: odroidxu-ts as /devices/platform/s3c2440-i2c.0/i2c-0/0-0048/input/input1
[ 3.445611] --------------------------------------------------------
[ 3.451196] TOUCH SCREEN INFORMATION
[ 3.455664] --------------------------------------------------------
[ 3.462003] TOUCH INPUT Name = odroidxu-ts
[ 3.466073] TOUCH ABS X MAX = 1280, TOUCH ABS X MIN = 0
[ 3.471280] TOUCH ABS Y MAX = 720, TOUCH ABS Y MIN = 0
[ 3.476394] Dummy Touchscreen driver!
[ 3.480007] --------------------------------------------------------
[ 3.486640] i2c-core: driver [odroid-ts] using legacy suspend method
[ 3.492705] i2c-core: driver [odroid-ts] using legacy resume method
[ 3.500301] max77802_rtc_probe
[ 3.540808] max77802-rtc max77802-rtc: rtc init
[ 3.543874] max77802_rtc_set_time: 112/0/1 0:0:0(0)
[ 3.555808] max77802_rtc_set_time: task=swapper/0[1]
[ 3.559301] max77802-rtc max77802-rtc: max77802_rtc_enable_wtsr: enable WTSR
[ 3.596068] max77802_rtc_read_time: 112/0/1 0:0:0(0)
[ 3.606064] max77802_rtc_read_alarm: 100/0/1 0:0:0(0)
[ 3.616054] max77802_rtc_read_time: 112/0/1 0:0:0(0)
[ 3.620006] max77802-rtc max77802-rtc: rtc core: registered max77802-rtc as rtc0
[ 3.626985] usb 1-3: new high-speed USB device number 3 using s5p-ehci
[ 3.633487] max77802_irq_unmask: group=2, cur=0xfd
[ 3.638893] i2c /dev entries driver
[ 3.643885] lirc_dev: IR Remote Control driver registered, major 250
[ 3.648891] IR NEC protocol handler initialized
[ 3.653404] IR RC5(x) protocol handler initialized
[ 3.658163] IR RC6 protocol handler initialized
[ 3.662664] IR JVC protocol handler initialized
[ 3.667172] IR Sony protocol handler initialized
[ 3.671771] IR RC5 (streamzap) protocol handler initialized
[ 3.677323] IR SANYO protocol handler initialized
[ 3.682002] IR MCE Keyboard/mouse protocol handler initialized
[ 3.687836] IR LIRC bridge handler initialized
[ 3.692388] gspca_main: v2.14.0 registered
[ 3.696684] exynos-mdev.0: Media0[0xde1e7800] was registered successfully
[ 3.703474] exynos-mdev.1: Media1[0xde1e7c00] was registered successfully
[ 3.710238] exynos-mdev.2: Media2[0xddc0c000] was registered successfully
[ 3.717068] s5p-mipi-csis.0
[ 3.717073] : s5pcsis_probe : csis0 probe success
[ 3.724183] s5p-mipi-csis.1
[ 3.724187] : s5pcsis_probe : csis1 probe success
[ 3.731651] s5p-mipi-csis.2
[ 3.731655] : s5pcsis_probe : csis2 probe success
[ 3.739728] [INFO]flite_probe:2214: FIMC-LITE0 probe success
[ 3.744993] [INFO]flite_probe:2214: FIMC-LITE1 probe success
[ 3.750789] [INFO]flite_probe:2214: FIMC-LITE2 probe success
[ 3.757357] [INFO]gsc_probe:1559: gsc-0 registered successfully
[ 3.762991] [INFO]gsc_probe:1559: gsc-1 registered successfully
[ 3.769136] hub 1-3:1.0: USB hub found
[ 3.771541] hub 1-3:1.0: 3 ports detected
[ 3.775874] [INFO]gsc_probe:1559: gsc-2 registered successfully
[ 3.782831] [INFO]gsc_probe:1559: gsc-3 registered successfully
[ 3.787610] exynos5-scaler exynos5-scaler.0: ++sc_probe
[ 3.793007] exynos5-scaler exynos5-scaler.0: scaler registered successfully
[ 3.799791] Initialize JPEG driver
[ 3.803286] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video12
[ 3.809828] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video11
[ 3.816457] Exynos Graphics 2D driver, (c) 2011 Samsung Electronics
[ 3.822654] [fimg2d_probe] base address: 0x10850000
[ 3.827287] [fimg2d_probe] irq: 123
[ 3.830804] [fimg2d_clk_setup] aclk_acp(266000000) pclk_acp(133000000)
[ 3.837274] [fimg2d_clk_setup] gate clk: fimg2d
[ 3.841771] [fimg2d_probe] enable runtime pm
[ 3.846014] [fimg2d_probe] register sysmmu page fault handler
[ 3.852261] EXYNOS MFC V4L2 Driver, (c) 2010 Samsung Electronics
[ 3.858305] s5p-mfc s5p-mfc-v6: decoder registered as /dev/video6
[ 3.864116] s5p-mfc s5p-mfc-v6: encoder registered as /dev/video7
[ 3.870569] i2c i2c-2: attached exynos hdcp into i2c adapter successfully
[ 3.876838] i2c-core: driver [exynos_hdcp] using legacy suspend method
[ 3.883174] i2c-core: driver [exynos_hdcp] using legacy resume method
[ 3.889829] Samsung HDMI output driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 3.897414] s5p-hdmi exynos5-hdmi: hdmi ip version = 2
[ 3.903074] s5p-hdmi exynos5-hdmi: probe sucessful
[ 3.907335] Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 3.916171] s5p-mixer s5p-mixer: probe start
[ 3.918975] s5p-mixer s5p-mixer: mixer ip version = 2
[ 3.924219] s5p-mixer s5p-mixer: resources acquired
[ 3.928908] s5p-mixer s5p-mixer: added output 'S5P HDMI connector' from module 's5p-hdmi'
[ 3.937372] s5p-mixer s5p-mixer: registered layer mxr0_graph0 as /dev/video16
[ 3.944452] s5p-mixer s5p-mixer: registered layer mxr0_graph1 as /dev/video17
[ 3.951629] s5p-mixer s5p-mixer: registered layer mxr1_graph2 as /dev/video18
[ 3.958678] s5p-mixer s5p-mixer: registered layer mxr1_graph3 as /dev/video19
[ 3.965493] s5p-mixer s5p-mixer: mixer0 create links
[ 3.970432] s5p-mixer s5p-mixer: mixer1 create links
[ 3.975393] s5p-mixer s5p-mixer: mixer links are created successfully
[ 3.981803] s5p-mixer s5p-mixer: probe successful
[ 3.986696] S5P CEC for Exynos4 Driver, (c) 2009 Samsung Electronics
[ 3.993193] s5p-tvout-cec s5p-tvout-cec: probe successful
[ 3.998440] exynos-rot exynos-rot: ++rot_probe
[ 4.002924] exynos-rot exynos-rot: rotator registered successfully
[ 4.008972] Initialize JPEG Hx driver
[ 4.012823] exynos5-jpeg-hx exynos5-jpeg-hx: JPEG driver is registered to /dev/video14
[ 4.020589] exynos5-jpeg-hx exynos5-jpeg-hx: JPEG driver is registered to /dev/video13
[ 4.028671] usbcore: registered new interface driver uvcvideo
[ 4.033909] USB Video Class driver (1.1.1)
[ 4.038241] samsung-fake-battery samsung-fake-battery: samsung_fake_bat_probe
[ 4.048005] Exynos: Kernel Thermal management registered
[ 4.052211] s3c2410_wdt: S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 4.059331] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq disabled
[ 4.067844] device-mapper: uevent: version 1.0.3
[ 4.071836] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 4.079887] usbcore: registered new interface driver btusb
[ 4.085502] cpuidle: using governor ladder
[ 4.089603] cpuidle: using governor menu
[ 4.093500] sdhci: Secure Digital Host Controller Interface driver
[ 4.099235] sdhci: Copyright(c) Pierre Ossman
[ 4.104147] Synopsys Designware Multimedia Card Interface Driver
[ 4.109489] dw_mmc dw_mmc.2: Using internal DMA controller.
[ 4.115491] dw_mmc dw_mmc.2: no vmmc regulator found
[ 4.120053] dw_mmc dw_mmc.2: no vqmmc regulator found
[ 4.126860] dw_mmc dw_mmc.2: Version ID is 241a
[ 4.129929] dw_mmc dw_mmc.2: DW MMC controller at irq 109, 64 bit host data width, 128 deep fifo
[ 4.138794] dw_mmc dw_mmc.0: Using internal DMA controller.
[ 4.144711] dw_mmc dw_mmc.0: vmmc regulator found
[ 4.149134] dw_mmc dw_mmc.0: vqmmc regulator found
[ 4.155542] dw_mmc dw_mmc.0: Version ID is 241a
[ 4.158640] dw_mmc dw_mmc.0: DW MMC controller at irq 107, 64 bit host data width, 128 deep fifo
[ 4.161731] mmc_host mmc0: Bus speed (slot 0) = 20000000Hz (slot req 400000Hz, actual 400000HZ div = 25)
[ 4.179148] usbcore: registered new interface driver usbhid
[ 4.183287] usbhid: USB HID core driver
[ 4.188015] --------------------------------------------------------
[ 4.193447] odroid_sysfs_init(472) : Sleep Disable Flag SET!!(Wake_lock_init)
[ 4.200541] --------------------------------------------------------
[ 4.257863] mmc_host mmc0: Bus speed (slot 0) = 40000000Hz (slot req 50000000Hz, actual 40000000HZ div = 0)
[ 4.266401] mmc0: new high speed SDHC card at address aaaa
[ 4.272979] mmcblk0: mmc0:aaaa SU32G 29.7 GiB
[ 4.280298] mmcblk0: p1 p2 p3
[ 4.311092] mmc_host mmc1: Bus speed (slot 0) = 20000000Hz (slot req 400000Hz, actual 400000HZ div = 25)
[ 4.360893] mmc_host mmc1: Bus speed (slot 0) = 20000000Hz (slot req 313726Hz, actual 312500HZ div = 32)
[ 4.401187] usb 1-3.1: new high-speed USB device number 4 using s5p-ehci
[ 4.515592] scsi0 : usb-storage 1-3.1:1.0
[ 5.045935] hot state 0 to 1
[ 5.205772] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 6.205768] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 6.209399] INA231 4-0040: I2C write error: (-121) reg: 0x0
[ 6.214935] ============= Probe INA231 Fail! : sensor_arm (0xFFFFFF87) =============
[ 6.222754] INA231: probe of 4-0040 failed with error -121
[ 7.225768] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 7.542533] scsi 0:0:0:0: Direct-Access Samsung M3 Portable 3 PQ: 0 ANSI: 6
[ 7.552499] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8.225800] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 8.229401] INA231 4-0041: I2C write error: (-121) reg: 0x0
[ 8.234962] ============= Probe INA231 Fail! : sensor_mem (0xFFFFFF87) =============
[ 8.242781] INA231: probe of 4-0041 failed with error -121
[ 9.245802] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 9.564780] sd 0:0:0:0: [sda] 1953504688 512-byte logical blocks: (1.00 TB/931 GiB)
[ 9.574543] sd 0:0:0:0: [sda] Write Protect is off
[ 9.578879] sd 0:0:0:0: [sda] No Caching mode page present
[ 9.583387] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.593125] sd 0:0:0:0: [sda] No Caching mode page present
[ 9.597199] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.669547] sda: sda1
[ 9.676088] sd 0:0:0:0: [sda] No Caching mode page present
[ 9.680113] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.686240] sd 0:0:0:0: [sda] Attached SCSI disk
[ 10.245768] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 10.249367] INA231 4-0044: I2C write error: (-121) reg: 0x0
[ 10.254927] ============= Probe INA231 Fail! : sensor_g3d (0xFFFFFF87) =============
[ 10.262769] INA231: probe of 4-0044 failed with error -121
[ 11.265768] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 12.265767] exynos5-i2c exynos5-hs-i2c.0: tx timeout
[ 12.269367] INA231 4-0045: I2C write error: (-121) reg: 0x0
[ 12.274927] ============= Probe INA231 Fail! : sensor_kfc (0xFFFFFF87) =============
[ 12.282744] INA231: probe of 4-0045 failed with error -121
[ 12.288687] i2c-core: driver [INA231] using legacy suspend method
[ 12.294276] i2c-core: driver [INA231] using legacy resume method
[ 12.300400]
[ 12.300405] =================== ioboard_keyled_probe ===================
[ 12.300411]
[ 13.145768] ioboard-bh1780 10-0029: I2C write byte error: data=0x8b
[ 13.151153] i2c-core: driver [ioboard-bh1780] using legacy suspend method
[ 13.157371] i2c-core: driver [ioboard-bh1780] using legacy resume method
[ 17.360803] bmp180_read_store_eeprom_val: Cannot read EEPROM values
[ 17.365602] bmp180_probe: Reading the EEPROM failed
[ 17.370985] i2c-core: driver [ioboard-bmp180] using legacy suspend method
[ 17.377262] i2c-core: driver [ioboard-bmp180] using legacy resume method
[ 17.384018]
[ 17.384022] =================== ioboard_adc_probe ===================
[ 17.384028]
[ 17.393650] -------------------- ioboard_spi_probe -----------------------
[ 17.401774] usbcore: registered new interface driver snd-usb-audio
[ 17.410427] soc-audio soc-audio.0: ASoC machine Odroid-max98090 should use snd_soc_register_card()
[ 17.418465] samsung-i2s samsung-i2s.0: EPLL rate = 400000000
[ 17.423598] samsung-i2s samsung-i2s.0: SRP rate = 100000000
[ 17.429148] samsung-i2s samsung-i2s.0: BUS rate = 50000000
[ 17.435544] max98090 1-0010: revision 0x43
[ 17.440831] [MAX98090] max98090_set_record_main_mic(151)
[ 17.446134] asoc: max98090-aif1 samsung-i2s.0 mapping ok
[ 17.451087] asoc: max98090-aif1 samsung-i2s.0 mapping ok
[ 17.459936] GACT probability NOT on
[ 17.461999] Mirror/redirect action on
[ 17.465604] u32 classifier
[ 17.468313] Actions configured
[ 17.471698] Netfilter messages via NETLINK v0.30.
[ 17.476432] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 17.483384] ctnetlink v0.93: registering with nfnetlink.
[ 17.487809] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 17.494689] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 17.501197] xt_time: kernel timezone is -0000
[ 17.505142] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.510316] arp_tables: (C) 2002 David S. Miller
[ 17.514764] TCP: bic registered
[ 17.517836] TCP: cubic registered
[ 17.521129] TCP: westwood registered
[ 17.524657] TCP: htcp registered
[ 17.529971] NET: Registered protocol family 10
[ 17.533757] Mobile IPv6
[ 17.535403] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.540969] IPv6 over IPv4 tunneling driver
[ 17.547957] NET: Registered protocol family 17
[ 17.550991] NET: Registered protocol family 15
[ 17.555532] Bluetooth: RFCOMM TTY layer initialized
[ 17.560257] Bluetooth: RFCOMM socket layer initialized
[ 17.565360] Bluetooth: RFCOMM ver 1.11
[ 17.569084] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.574374] Bluetooth: BNEP filters: protocol multicast
[ 17.579582] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 17.586055] NET: Registered protocol family 33
[ 17.592763] RxRPC: Registered security type 2 'rxkad'
[ 17.596421] NET: Registered protocol family 35
[ 17.600958] lib80211: common routines for IEEE802.11 drivers
[ 17.606453] Registering the dns_resolver key type
[ 17.611532] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 17.618767] Registering SWP/SWPB emulation handler
[ 17.628338] HDMI phy power off : 1
[ 17.745811] s5p-mipi-dsim s5p-mipi-dsim.1: DSI Master driver has been completed.
[ 17.751783] s5p-mipi-dsim s5p-mipi-dsim.1: DSI Master state is stop state
[ 17.758540] s5p-mipi-dsim s5p-mipi-dsim.1: dsim_lcd_drv->probe is NULL.
[ 18.035222] s5p-mipi-dsim s5p-mipi-dsim.1: mipi-dsi driver(RGB mode) has been probed.
[ 18.054833] s3c-fb exynos5-fb.1: failed to find bootloader framebuffer
[ 18.059934] s3c-fb exynos5-fb.1: couldn't copy bootloader framebuffer into default window; clearing instead
[ 18.088290] s3c-fb exynos5-fb.1: window 0: fb
[ 18.093422] vddq_lcd: incomplete constraints, leaving on
[ 18.097382]
[ 18.097386] uiCount = 1800
[ 18.101535] PA FB = 0xB6300000, bits per pixel = 32
[ 18.106394] screen width=1280 height=720 va=0x0xres_virtual = 1280, yres_virtual = 720, xoffset = 0, yoffset = 0
[ 18.116545] fb_size=7372800
[ 18.119288] Back frameBuffer[0].VAddr=00384000 PAddr=b5e84000 size=3686400
[ 18.136159] max77802_rtc_read_time: 112/0/1 0:0:14(0)
[ 18.139911] max77802-rtc max77802-rtc: setting system clock to 2012-01-01 00:00:14 UTC (1325376014)
[ 18.148803] CPUFREQ of CA7 L0 : 1237500 uV
[ 18.152947] CPUFREQ of CA7 L1 : 1237500 uV
[ 18.157108] CPUFREQ of CA7 L2 : 1175000 uV
[ 18.161268] CPUFREQ of CA7 L3 : 1112500 uV
[ 18.165405] CPUFREQ of CA7 L4 : 1050000 uV
[ 18.169592] CPUFREQ of CA7 L5 : 1000000 uV
[ 18.173757] CPUFREQ of CA7 L6 : 950000 uV
[ 18.177832] CPUFREQ of CA7 L7 : 950000 uV
[ 18.181906] CPUFREQ of CA7 L8 : 950000 uV
[ 18.186006] CPUFREQ of CA7 L9 : 950000 uV
[ 18.190033] CPUFREQ of CA7 L10 : 950000 uV
[ 18.194224] CPUFREQ of CA7 L11 : 950000 uV
[ 18.198464] CPUFREQ of CA15 L0 : 1237500 uV
[ 18.202547] CPUFREQ of CA15 L1 : 1237500 uV
[ 18.206708] CPUFREQ of CA15 L2 : 1237500 uV
[ 18.210876] CPUFREQ of CA15 L3 : 1187500 uV
[ 18.215008] CPUFREQ of CA15 L4 : 1150000 uV
[ 18.219201] CPUFREQ of CA15 L5 : 1125000 uV
[ 18.223363] CPUFREQ of CA15 L6 : 1087500 uV
[ 18.227524] CPUFREQ of CA15 L7 : 1050000 uV
[ 18.231692] CPUFREQ of CA15 L8 : 1012500 uV
[ 18.235848] CPUFREQ of CA15 L9 : 987500 uV
[ 18.239896] CPUFREQ of CA15 L10 : 950000 uV
[ 18.244086] CPUFREQ of CA15 L11 : 912500 uV
[ 18.248249] CPUFREQ of CA15 L12 : 900000 uV
[ 18.252411] CPUFREQ of CA15 L13 : 900000 uV
[ 18.256575] CPUFREQ of CA15 L14 : 900000 uV
[ 18.260708] CPUFREQ of CA15 L15 : 900000 uV
[ 18.264896] CPUFREQ of CA15 L16 : 900000 uV
[ 18.269066] CPUFREQ of CA15 L17 : 900000 uV
[ 18.273225] CPUFREQ of CA15 L18 : 900000 uV
[ 18.277467] fout_apll[900000000]
[ 18.281632] INT 800000Khz ASV is 1025000uV
[ 18.284650] INT 700000Khz ASV is 1000000uV
[ 18.288766] INT 650000Khz ASV is 1000000uV
[ 18.292820] INT 600000Khz ASV is 1000000uV
[ 18.296894] INT 550000Khz ASV is 1000000uV
[ 18.300984] INT 400000Khz ASV is 1000000uV
[ 18.305020] INT 267000Khz ASV is 1000000uV
[ 18.309124] INT 200000Khz ASV is 1000000uV
[ 18.313196] INT 160000Khz ASV is 1000000uV
[ 18.317272] INT 100000Khz ASV is 1000000uV
[ 18.321348] INT 50000Khz ASV is 1000000uV
[ 18.327519] MIF 800000Khz ASV is 987500uV
[ 18.330056] MIF 667000Khz ASV is 1025000uV
[ 18.334154] MIF 533000Khz ASV is 1025000uV
[ 18.338227] MIF 400000Khz ASV is 900000uV
[ 18.342213] MIF 267000Khz ASV is 1025000uV
[ 18.346289] MIF 200000Khz ASV is 850000uV
[ 18.350258] MIF 160000Khz ASV is 1025000uV
[ 18.354356] MIF 100000Khz ASV is 850000uV
[ 18.358344] S divider change for DFS of MIF block
[ 18.531440] init_volt[987500], freq[800000]
[ 18.535277] ALSA device list:
[ 18.537122] #0: Odroid-max98090
[ 18.540693] Freeing init memory: 252K
[ 18.544060] Write protecting the kernel text section c0008000 - c0952000
[ 18.551061] rodata_test: attempting to write to read-only section:
[ 18.556896] write to read-only section trapped, success
[ 18.770906] systemd[1]: systemd 204 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 18.782039] systemd[1]: Running in initial RAM disk.
Welcome to [ 18.788279] systemd[1]: Failed to insert module 'autofs4'
[ 18.793600] systemd[1]: No hostname configured.
[ 18.797944] systemd[1]: Set hostname to .
[0;34mFedora 19 (Schrödinger’s Cat) dracut-029-2.fc19 (Initramfs)[0m!
Richard WM Jones 